餐飲業安裝靜電油煙凈化設備時，不可避免地會遇到一些小問題，但并非廠家油煙凈化器的質量問題，大多是安裝和運輸過程中因其他或人為原因造成的。要是出了故障，該怎么辦？下面是油煙凈化器的常見故障及排除方法。
The catering industry will inevitably encounter some small problems when installing electrostatic fume purification equipment, but it is not the quality problem of the manufacturer's fume purifier, which is mostly caused by other or man-made reasons during installation and transportation. What if something goes wrong? The following are the common faults and troubleshooting methods of oil fume purifier.
油煙凈化器不能啟動。
The fume purifier cannot be started.
1.如電源線接錯，請重新接通電源，重新設置保護空氣開關，觀察高壓模塊是否正常工作。
1. If the power line is connected incorrectly, please reconnect the power supply, reset the protective air switch, and observe whether the high-voltage module works normally.
2.原因及解決辦法：檢測電線絕緣損壞或漏電，更換電線。
2. Causes and solutions: check the insulation damage or leakage of wires, and replace the wires.
3.高電壓模組內部短路、更換或維修、油煙凈化器電源或漏電保護開關的質量問題。
3. Internal short circuit, replacement or maintenance of high-voltage module, quality problems of fume purifier power supply or leakage protection switch.
設備運行時仍然有刺耳的聲音，甚有火花。
There are still harsh sounds and even sparks when the equipment is running.
1.檢查油煙凈化器電壓是否過高。電壓適時調節(在人員指導下)。左下方的藍色箭頭，由左向小，由右向大。標準安培計顯示范圍在5-12a之間。
1. Check whether the voltage of the fume purifier is too high. Adjust the voltage in time (under the guidance of professionals). The blue arrow at the bottom left, from left to small, from right to large. The display range of standard ammeter is between 5-12a.
2.檢查機箱電場方向是否正確。變化電場的方向，在運動的兩邊都有電場方向標志。
2. Check whether the electric field direction of the chassis is correct. Change the direction of the electric field, and there are signs of the direction of the electric field on both sides of the movement.
3.檢查高低壓接線是否符合電場。適當的接線方式是電場的高壓區對應高壓接線，電場的低壓區對應低電壓區，高壓線對應鋸齒板放電，低壓線對應吸附板放電。
3. Check whether the high and low voltage wiring conforms to the electric field. The proper wiring method is that the high-voltage area of the electric field corresponds to the high-voltage wiring, the low-voltage area of the electric field corresponds to the low-voltage area, the high-voltage line corresponds to the sawtooth plate discharge, and the low-voltage line corresponds to the adsorption plate discharge.
4.檢查電場是否有雜物、極板變形、絕緣材料損壞。電場中的雜質，用手工修復電場吸附板的變形，替換或修復絕緣材料。
4. Check whether there are sundries in the electric field, pole plate deformation and insulation material damage. Remove the impurities in the electric field, manually repair the deformation of the electric field adsorption plate, and replace or repair the insulating material.
5.清洗后電場的濕度太大。風干或風干電場，注意電場內是否有雜物。
5. The humidity of the electric field after cleaning is too high. Air dry or air dry the electric field, and pay attention to whether there are sundries in the electric field.
Jinan lampblack purifier has induction power supply, and the battery works normally, but the equipment has no reaction, and the battery works normally.
1.當出現故障時，檢查外箱體是否接地，確保電場電極接觸。
1. In case of failure, check whether the outer box is grounded to ensure that the electrode of the electric field contacts.
2.檢查電絕緣體或絕緣瓷是否完好，調整電極板接觸，確保接觸良好。
2. Check whether the electrical insulator or insulating porcelain is in good condition, and adjust the electrode plate contact to ensure good contact.
At the end, it is necessary to remind the precautions: when using the lampblack purifier, we should develop the habit of regular inspection, regular cleaning and regular maintenance, do a good job in daily maintenance, protect the operation of the equipment, and extend the service life of the equipment. Come to our website for more relevant content http://www.www.qa48.com OK.
上一篇：通風管道的加工要多注意事項
下一篇：廚房排煙的設計與安裝事項
